1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2022 Josua Mayer <josua@solid-run.com>
*
* Copyright (C) 2015 Freescale Semiconductor, Inc.
*
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*
* Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>
*
* Based on SPL code from Solidrun tree, which is:
* Author: Tungyi Lin <tungyilin1127@gmail.com>
*
* Derived from EDM_CF_IMX6 code by TechNexion,Inc
* Ported to SolidRun microSOM by Rabeeh Khoury <rabeeh@solid-run.com>
*/
#include <common.h>
#include <image.h>
#include <init.h>
#include <log.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/mxc_hdmi.h>
#include <env.h>
#include <asm/global_data.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/sata.h>
#include <asm/mach-imx/video.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <malloc.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
#include <spl.h>
#include <usb.h>
#include <usb/ehci-ci.h>
#include <netdev.h>
#include <phy.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USB_H1_VBUS IMX_GPIO_NR(1, 0)
enum board_type {
CUBOXI = 0x00,
HUMMINGBOARD = 0x01,
HUMMINGBOARD2 = 0x02,
UNKNOWN = 0x03,
};
static struct gpio_desc board_detect_desc[5];
#define MEM_STRIDE 0x4000000
static u32 get_ram_size_stride_test(u32 *base, u32 maxsize)
{
volatile u32 *addr;
u32 save[64];
u32 cnt;
u32 size;
int i = 0;
/* First save the data */
for (cnt = 0; cnt < maxsize; cnt += MEM_STRIDE) {
addr = (volatile u32 *)((u32)base + cnt); /* pointer arith! */
sync ();
save[i++] = *addr;
sync ();
}
/* First write a signature */
* (volatile u32 *)base = 0x12345678;
for (size = MEM_STRIDE; size < maxsize; size += MEM_STRIDE) {
* (volatile u32 *)((u32)base + size) = size;
sync ();
if (* (volatile u32 *)((u32)base) == size) { /* We reached the overlapping address */
break;
}
}
/* Restore the data */
for (cnt = (maxsize - MEM_STRIDE); i > 0; cnt -= MEM_STRIDE) {
addr = (volatile u32 *)((u32)base + cnt); /* pointer arith! */
sync ();
*addr = save[i--];
sync ();
}
return (size);
}
int dram_init(void)
{
u32 max_size = imx_ddr_size();
gd->ram_size = get_ram_size_stride_test((u32 *) CONFIG_SYS_SDRAM_BASE,
(u32)max_size);
return 0;
}
static iomux_v3_cfg_t const uart1_pads[] = {
IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
static iomux_v3_cfg_t const usdhc2_pads[] = {
IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
};
static iomux_v3_cfg_t const usdhc3_pads[] = {
IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
};
static iomux_v3_cfg_t const board_detect[] = {
/* These pins are for sensing if it is a CuBox-i or a HummingBoard */
IOMUX_PADS(PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_EIM_DA4__GPIO3_IO04 | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
static iomux_v3_cfg_t const som_rev_detect[] = {
/* These pins are for sensing if it is a CuBox-i or a HummingBoard */
IOMUX_PADS(PAD_CSI0_DAT14__GPIO6_IO00 | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_CSI0_DAT18__GPIO6_IO04 | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
static void setup_iomux_uart(void)
{
SETUP_IOMUX_PADS(uart1_pads);
}
int board_mmc_get_env_dev(int devno)
{
return devno;
}
#ifdef CONFIG_VIDEO_IPUV3
static void do_enable_hdmi(struct display_info_t const *dev)
{
imx_enable_hdmi_phy();
}
struct display_info_t const displays[] = {
{
.bus = -1,
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_hdmi,
.enable = do_enable_hdmi,
.mode = {
.name = "HDMI",
/* 1024x768@60Hz (VESA)*/
.refresh = 60,
.xres = 1024,
.yres = 768,
.pixclock = 15384,
.left_margin = 160,
.right_margin = 24,
.upper_margin = 29,
.lower_margin = 3,
.hsync_len = 136,
.vsync_len = 6,
.sync = FB_SYNC_EXT,
.vmode = FB_VMODE_NONINTERLACED
}
}
};
size_t display_count = ARRAY_SIZE(displays);
static int setup_display(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
int reg;
int timeout = 100000;
enable_ipu_clock();
imx_setup_hdmi();
/* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
reg = readl(&ccm->analog_pll_video);
reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
writel(reg, &ccm->analog_pll_video);
writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
writel(reg, &ccm->analog_pll_video);
while (timeout--)
if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
break;
if (timeout < 0) {
printf("Warning: video pll lock timeout!\n");
return -ETIMEDOUT;
}
reg = readl(&ccm->analog_pll_video);
reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
writel(reg, &ccm->analog_pll_video);
/* gate ipu1_di0_clk */
clrbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
/* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */
reg = readl(&ccm->chsccdr);
reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
(6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
(0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &ccm->chsccdr);
/* enable ipu1_di0_clk */
setbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
return 0;
}
#endif /* CONFIG_VIDEO_IPUV3 */
static int setup_fec(void)
{
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
int ret;
ret = enable_fec_anatop_clock(0, ENET_25MHZ);
if (ret)
return ret;
/* set gpr1[ENET_CLK_SEL] */
setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
return 0;
}
int board_early_init_f(void)
{
setup_iomux_uart();
#ifdef CONFIG_CMD_SATA
setup_sata();
#endif
setup_fec();
return 0;
}
int board_init(void)
{
int ret = 0;
/* address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_VIDEO_IPUV3
ret = setup_display();
#endif
return ret;
}
static int request_detect_gpios(void)
{
int node;
int ret;
node = fdt_node_offset_by_compatible(gd->fdt_blob, 0,
"solidrun,hummingboard-detect");
if (node < 0)
return -ENODEV;
ret = gpio_request_list_by_name_nodev(offset_to_ofnode(node),
"detect-gpios", board_detect_desc,
ARRAY_SIZE(board_detect_desc), GPIOD_IS_IN);
return ret;
}
static int free_detect_gpios(void)
{
return gpio_free_list_nodev(board_detect_desc,
ARRAY_SIZE(board_detect_desc));
}
static enum board_type board_type(void)
{
int val1, val2, val3;
SETUP_IOMUX_PADS(board_detect);
/*
* Machine selection -
* Machine val1, val2, val3
* ----------------------------
* HB2 x x 0
* HB rev 3.x x 0 x
* CBi 0 1 x
* HB 1 1 x
*/
gpio_direction_input(IMX_GPIO_NR(2, 8));
val3 = gpio_get_value(IMX_GPIO_NR(2, 8));
if (val3 == 0)
return HUMMINGBOARD2;
gpio_direction_input(IMX_GPIO_NR(3, 4));
val2 = gpio_get_value(IMX_GPIO_NR(3, 4));
if (val2 == 0)
return HUMMINGBOARD;
gpio_direction_input(IMX_GPIO_NR(4, 9));
val1 = gpio_get_value(IMX_GPIO_NR(4, 9));
if (val1 == 0) {
return CUBOXI;
} else {
return HUMMINGBOARD;
}
}
static bool is_rev_15_som(void)
{
int val1, val2;
SETUP_IOMUX_PADS(som_rev_detect);
val1 = gpio_get_value(IMX_GPIO_NR(6, 0));
val2 = gpio_get_value(IMX_GPIO_NR(6, 4));
if (val1 == 1 && val2 == 0)
return true;
return false;
}
static bool has_emmc(void)
{
struct mmc *mmc;
mmc = find_mmc_device(2);
if (!mmc)
return 0;
return (mmc_get_op_cond(mmc, true) < 0) ? 0 : 1;
}
int checkboard(void)
{
request_detect_gpios();
switch (board_type()) {
case CUBOXI:
puts("Board: MX6 Cubox-i");
break;
case HUMMINGBOARD:
puts("Board: MX6 HummingBoard");
break;
case HUMMINGBOARD2:
puts("Board: MX6 HummingBoard2");
break;
case UNKNOWN:
default:
puts("Board: Unknown\n");
goto out;
}
if (is_rev_15_som())
puts(" (som rev 1.5)\n");
else
puts("\n");
free_detect_gpios();
out:
return 0;
}
static int find_ethernet_phy(void)
{
struct mii_dev *bus = NULL;
struct phy_device *phydev = NULL;
int phy_addr = -ENOENT;
#ifdef CONFIG_FEC_MXC
bus = fec_get_miibus(ENET_BASE_ADDR, -1);
if (!bus)
return -ENOENT;
// scan address 0, 1, 4
phydev = phy_find_by_mask(bus, 0b00010011);
if (!phydev) {
free(bus);
return -ENOENT;
}
pr_debug("%s: detected ethernet phy at address %d\n", __func__, phydev->addr);
phy_addr = phydev->addr;
free(phydev);
#endif
return phy_addr;
}
#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
/*
* Configure the correct ethernet PHYs nodes in device-tree:
* - AR8035 at addresses 0 or 4: Cubox
* - AR8035 at address 0: HummingBoard, HummingBoard 2
* - ADIN1300 at address 1: since SoM rev 1.9
*/
int ft_board_setup(void *fdt, struct bd_info *bd)
{
int node_phy0, node_phy1, node_phy4;
int ret, phy;
bool enable_phy0 = false, enable_phy1 = false, enable_phy4 = false;
enum board_type board;
// detect device
request_detect_gpios();
board = board_type();
free_detect_gpios();
// detect phy
phy = find_ethernet_phy();
if (phy == 0 || phy == 4) {
enable_phy0 = true;
switch (board) {
case HUMMINGBOARD:
case HUMMINGBOARD2:
/* atheros phy may appear only at address 0 */
break;
case CUBOXI:
case UNKNOWN:
default:
/* atheros phy may appear at either address 0 or 4 */
enable_phy4 = true;
}
} else if (phy == 1) {
enable_phy1 = true;
} else {
pr_err("%s: couldn't detect ethernet phy, not patching dtb!\n", __func__);
return 0;
}
// update all phy nodes status
node_phy0 = fdt_path_offset(fdt, "/soc/bus@2100000/ethernet@2188000/mdio/ethernet-phy@0");
ret = fdt_setprop_string(fdt, node_phy0, "status", enable_phy0 ? "okay" : "disabled");
if (ret < 0 && enable_phy0)
pr_err("%s: failed to enable ethernet phy at address 0 in dtb!\n", __func__);
node_phy1 = fdt_path_offset(fdt, "/soc/bus@2100000/ethernet@2188000/mdio/ethernet-phy@1");
ret = fdt_setprop_string(fdt, node_phy1, "status", enable_phy1 ? "okay" : "disabled");
if (ret < 0 && enable_phy1)
pr_err("%s: failed to enable ethernet phy at address 1 in dtb!\n", __func__);
node_phy4 = fdt_path_offset(fdt, "/soc/bus@2100000/ethernet@2188000/mdio/ethernet-phy@4");
ret = fdt_setprop_string(fdt, node_phy4, "status", enable_phy4 ? "okay" : "disabled");
if (ret < 0 && enable_phy4)
pr_err("%s: failed to enable ethernet phy at address 4 in dtb!\n", __func__);
return 0;
}
#endif
/* Override the default implementation, DT model is not accurate */
int show_board_info(void)
{
return checkboard();
}
int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
request_detect_gpios();
switch (board_type()) {
case CUBOXI:
env_set("board_name", "CUBOXI");
break;
case HUMMINGBOARD:
env_set("board_name", "HUMMINGBOARD");
break;
case HUMMINGBOARD2:
env_set("board_name", "HUMMINGBOARD2");
break;
case UNKNOWN:
default:
env_set("board_name", "CUBOXI");
}
if (is_mx6dq())
env_set("board_rev", "MX6Q");
else
env_set("board_rev", "MX6DL");
if (is_rev_15_som())
env_set("som_rev", "V15");
if (has_emmc())
env_set("has_emmc", "yes");
free_detect_gpios();
#endif
return 0;
}
/*
* This is not a perfect match. Avoid dependency on the DM GPIO driver needed
* for accurate board detection. Hummingboard2 DT is good enough for U-Boot on
* all Hummingboard/Cubox-i platforms.
*/
int board_fit_config_name_match(const char *name)
{
char tmp_name[36];
snprintf(tmp_name, sizeof(tmp_name), "%s-hummingboard2-emmc-som-v15",
is_mx6dq() ? "imx6q" : "imx6dl");
return strcmp(name, tmp_name);
}
void board_boot_order(u32 *spl_boot_list)
{
struct src *psrc = (struct src *)SRC_BASE_ADDR;
unsigned int reg = readl(&psrc->sbmr1) >> 11;
u32 boot_mode = imx6_src_get_boot_mode() & IMX6_BMODE_MASK;
unsigned int bmode = readl(&src_base->sbmr2);
/* If bmode is serial or USB phy is active, return serial */
if (((bmode >> 24) & 0x03) == 0x01 || is_usbotg_phy_active()) {
spl_boot_list[0] = BOOT_DEVICE_BOARD;
return;
}
switch (boot_mode >> IMX6_BMODE_SHIFT) {
case IMX6_BMODE_SD:
case IMX6_BMODE_ESD:
case IMX6_BMODE_MMC:
case IMX6_BMODE_EMMC:
/*
* Upon reading BOOT_CFG register the following map is done:
* Bit 11 and 12 of BOOT_CFG register can determine the current
* mmc port
* 0x1 SD2
* 0x2 SD3
*/
reg &= 0x3; /* Only care about bottom 2 bits */
switch (reg) {
case 1:
SETUP_IOMUX_PADS(usdhc2_pads);
spl_boot_list[0] = BOOT_DEVICE_MMC1;
break;
case 2:
SETUP_IOMUX_PADS(usdhc3_pads);
spl_boot_list[0] = BOOT_DEVICE_MMC2;
break;
}
break;
default:
/* By default use USB downloader */
spl_boot_list[0] = BOOT_DEVICE_BOARD;
break;
}
/* As a last resort, use serial downloader */
spl_boot_list[1] = BOOT_DEVICE_BOARD;
}
#ifdef CONFIG_SPL_BUILD
#include <asm/arch/mx6-ddr.h>
static const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
.dram_sdclk_0 = 0x00020030,
.dram_sdclk_1 = 0x00020030,
.dram_cas = 0x00020030,
.dram_ras = 0x00020030,
.dram_reset = 0x000c0030,
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
.dram_sdba2 = 0x00000000,
.dram_sdodt0 = 0x00003030,
.dram_sdodt1 = 0x00003030,
.dram_sdqs0 = 0x00000030,
.dram_sdqs1 = 0x00000030,
.dram_sdqs2 = 0x00000030,
.dram_sdqs3 = 0x00000030,
.dram_sdqs4 = 0x00000030,
.dram_sdqs5 = 0x00000030,
.dram_sdqs6 = 0x00000030,
.dram_sdqs7 = 0x00000030,
.dram_dqm0 = 0x00020030,
.dram_dqm1 = 0x00020030,
.dram_dqm2 = 0x00020030,
.dram_dqm3 = 0x00020030,
.dram_dqm4 = 0x00020030,
.dram_dqm5 = 0x00020030,
.dram_dqm6 = 0x00020030,
.dram_dqm7 = 0x00020030,
};
static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = {
.dram_sdclk_0 = 0x00000028,
.dram_sdclk_1 = 0x00000028,
.dram_cas = 0x00000028,
.dram_ras = 0x00000028,
.dram_reset = 0x000c0028,
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
.dram_sdba2 = 0x00000000,
.dram_sdodt0 = 0x00003030,
.dram_sdodt1 = 0x00003030,
.dram_sdqs0 = 0x00000028,
.dram_sdqs1 = 0x00000028,
.dram_sdqs2 = 0x00000028,
.dram_sdqs3 = 0x00000028,
.dram_sdqs4 = 0x00000028,
.dram_sdqs5 = 0x00000028,
.dram_sdqs6 = 0x00000028,
.dram_sdqs7 = 0x00000028,
.dram_dqm0 = 0x00000028,
.dram_dqm1 = 0x00000028,
.dram_dqm2 = 0x00000028,
.dram_dqm3 = 0x00000028,
.dram_dqm4 = 0x00000028,
.dram_dqm5 = 0x00000028,
.dram_dqm6 = 0x00000028,
.dram_dqm7 = 0x00000028,
};
static const struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = {
.grp_ddr_type = 0x000C0000,
.grp_ddrmode_ctl = 0x00020000,
.grp_ddrpke = 0x00000000,
.grp_addds = 0x00000030,
.grp_ctlds = 0x00000030,
.grp_ddrmode = 0x00020000,
.grp_b0ds = 0x00000030,
.grp_b1ds = 0x00000030,
.grp_b2ds = 0x00000030,
.grp_b3ds = 0x00000030,
.grp_b4ds = 0x00000030,
.grp_b5ds = 0x00000030,
.grp_b6ds = 0x00000030,
.grp_b7ds = 0x00000030,
};
static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
.grp_ddr_type = 0x000c0000,
.grp_ddrmode_ctl = 0x00020000,
.grp_ddrpke = 0x00000000,
.grp_addds = 0x00000028,
.grp_ctlds = 0x00000028,
.grp_ddrmode = 0x00020000,
.grp_b0ds = 0x00000028,
.grp_b1ds = 0x00000028,
.grp_b2ds = 0x00000028,
.grp_b3ds = 0x00000028,
.grp_b4ds = 0x00000028,
.grp_b5ds = 0x00000028,
.grp_b6ds = 0x00000028,
.grp_b7ds = 0x00000028,
};
/* microSOM with Dual processor and 1GB memory */
static const struct mx6_mmdc_calibration mx6q_1g_mmcd_calib = {
.p0_mpwldectrl0 = 0x00000000,
.p0_mpwldectrl1 = 0x00000000,
.p1_mpwldectrl0 = 0x00000000,
.p1_mpwldectrl1 = 0x00000000,
.p0_mpdgctrl0 = 0x0314031c,
.p0_mpdgctrl1 = 0x023e0304,
.p1_mpdgctrl0 = 0x03240330,
.p1_mpdgctrl1 = 0x03180260,
.p0_mprddlctl = 0x3630323c,
.p1_mprddlctl = 0x3436283a,
.p0_mpwrdlctl = 0x36344038,
.p1_mpwrdlctl = 0x422a423c,
};
/* microSOM with Quad processor and 2GB memory */
static const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = {
.p0_mpwldectrl0 = 0x00000000,
.p0_mpwldectrl1 = 0x00000000,
.p1_mpwldectrl0 = 0x00000000,
.p1_mpwldectrl1 = 0x00000000,
.p0_mpdgctrl0 = 0x0314031c,
.p0_mpdgctrl1 = 0x023e0304,
.p1_mpdgctrl0 = 0x03240330,
.p1_mpdgctrl1 = 0x03180260,
.p0_mprddlctl = 0x3630323c,
.p1_mprddlctl = 0x3436283a,
.p0_mpwrdlctl = 0x36344038,
.p1_mpwrdlctl = 0x422a423c,
};
/* microSOM with Solo processor and 512MB memory */
static const struct mx6_mmdc_calibration mx6dl_512m_mmcd_calib = {
.p0_mpwldectrl0 = 0x0045004D,
.p0_mpwldectrl1 = 0x003A0047,
.p0_mpdgctrl0 = 0x023C0224,
.p0_mpdgctrl1 = 0x02000220,
.p0_mprddlctl = 0x44444846,
.p0_mpwrdlctl = 0x32343032,
};
/* microSOM with Dual lite processor and 1GB memory */
static const struct mx6_mmdc_calibration mx6dl_1g_mmcd_calib = {
.p0_mpwldectrl0 = 0x0045004D,
.p0_mpwldectrl1 = 0x003A0047,
.p1_mpwldectrl0 = 0x001F001F,
.p1_mpwldectrl1 = 0x00210035,
.p0_mpdgctrl0 = 0x023C0224,
.p0_mpdgctrl1 = 0x02000220,
.p1_mpdgctrl0 = 0x02200220,
.p1_mpdgctrl1 = 0x02040208,
.p0_mprddlctl = 0x44444846,
.p1_mprddlctl = 0x4042463C,
.p0_mpwrdlctl = 0x32343032,
.p1_mpwrdlctl = 0x36363430,
};
static struct mx6_ddr3_cfg mem_ddr_2g = {
.mem_speed = 1600,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
static struct mx6_ddr3_cfg mem_ddr_4g = {
.mem_speed = 1600,
.density = 4,
.width = 16,
.banks = 8,
.rowaddr = 16,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x0030FC03, &ccm->CCGR1);
writel(0x0FFFC000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0x00FFF300, &ccm->CCGR4);
writel(0x0F0000C3, &ccm->CCGR5);
writel(0x000003FF, &ccm->CCGR6);
}
static void spl_dram_init(int width)
{
struct mx6_ddr_sysinfo sysinfo = {
/* width of data bus: 0=16, 1=32, 2=64 */
.dsize = width / 32,
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 32Gb per CS */
.ncs = 1, /* single chip select */
.cs1_mirror = 0,
.rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
.rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
.walat = 1, /* Write additional latency */
.ralat = 5, /* Read additional latency */
.mif3_mode = 3, /* Command prediction working mode */
.bi_on = 1, /* Bank interleaving enabled */
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.ddr_type = DDR_TYPE_DDR3,
.refsel = 1, /* Refresh cycles at 32KHz */
.refr = 7, /* 8 refresh commands per refresh cycle */
};
if (is_mx6dq())
mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
else
mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
if (is_cpu_type(MXC_CPU_MX6D))
mx6_dram_cfg(&sysinfo, &mx6q_1g_mmcd_calib, &mem_ddr_2g);
else if (is_cpu_type(MXC_CPU_MX6Q))
mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g);
else if (is_cpu_type(MXC_CPU_MX6DL))
mx6_dram_cfg(&sysinfo, &mx6dl_1g_mmcd_calib, &mem_ddr_2g);
else if (is_cpu_type(MXC_CPU_MX6SOLO))
mx6_dram_cfg(&sysinfo, &mx6dl_512m_mmcd_calib, &mem_ddr_2g);
}
void board_init_f(ulong dummy)
{
/* setup AIPS and disable watchdog */
arch_cpu_init();
ccgr_init();
gpr_init();
/* iomux and setup of i2c */
board_early_init_f();
/* setup GP timer */
timer_init();
/* Enable device tree and early DM support*/
spl_early_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
/* DDR initialization */
if (is_cpu_type(MXC_CPU_MX6SOLO))
spl_dram_init(32);
else
spl_dram_init(64);
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
/* load/boot image from boot device */
board_init_r(NULL, 0);
}
#endif
|