| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit f1cb3476e48b60c450ec3a1d7da0805bffc6e43a ]
rsi_get_* functions rely on an offset variable from usb
input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000),
while 2-byte offset can be up to 0xFFFF. Thus a large offset
can cause out-of-bounds read.
The patch adds a bound checking condition when rcv_pkt_len is 0,
indicating it's USB. It's unclear whether this is triggerable
from other type of bus. The following check might help in that case.
offset > rcv_pkt_len - FRAME_DESC_SZ
The bug is trigerrable with conpromised/malfunctioning USB devices.
I tested the patch with the crashing input and got no more bug report.
Attached is the KASAN report from fuzzing.
BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x]
Read of size 2 at addr ffff888019439fdb by task RX-Thread/227
CPU: 0 PID: 227 Comm: RX-Thread Not tainted 5.6.0 #66
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
__kasan_report.cold+0x37/0x7c
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
kasan_report+0xe/0x20
rsi_read_pkt+0x42e/0x500 [rsi_91x]
rsi_usb_rx_thread+0x1b1/0x2fc [rsi_usb]
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __wake_up_common+0x10b/0x520
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
kthread+0x2b5/0x3b0
? kthread_create_on_node+0xd0/0xd0
ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxXS4wgu2OsmlVv@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 515e7184bdf0a3ebf1757cc77fb046b4fe282189 ]
When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.
==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...
Freed by task 111873:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
rsi_91x_init+0x741/0x8a0 [rsi_91x]
rsi_probe+0x9f/0x1750 [rsi_usb]
Stop thread before free 'common' and 'adapter' to fix it.
Fixes: 2108df3c4b18 ("rsi: add coex support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9b14ed6e11b72dd4806535449ca6c6962cb2369d upstream.
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber: 000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes: 716b840c7641 ("rsi: handle BT traffic in driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_main.c:157: warning: Function parameter or member 'rx_pkt' not described in 'rsi_read_pkt'
drivers/net/wireless/rsi/rsi_91x_main.c:157: warning: Excess function parameter 'rcv_pkt' description in 'rsi_read_pkt'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-18-lee.jones@linaro.org
|
|
The file header should not be kernel-doc. Add missing 'rec_pkt'
description. Update 'rsi_91x_init()'s parameter description.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_main.c:17: warning: Function parameter or member 'fmt' not described in 'pr_fmt'
drivers/net/wireless/rsi/rsi_91x_main.c:156: warning: Function parameter or member 'rx_pkt' not described in 'rsi_read_pkt'
drivers/net/wireless/rsi/rsi_91x_main.c:287: warning: Function parameter or member 'oper_mode' not described in 'rsi_91x_init'
drivers/net/wireless/rsi/rsi_91x_main.c:287: warning: Excess function parameter 'void' description in 'rsi_91x_init'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-3-lee.jones@linaro.org
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/rsi/rsi_91x_main.c: In function 'rsi_prepare_skb':
drivers/net/wireless/rsi/rsi_91x_main.c:127:24: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rsi/rsi_91x_main.c:124:28: warning:
variable 'info' set but not used [-Wunused-but-set-variable]
They're not used any more since 160ee2a11ce0 ("rsi: fill rx_params only once.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With the current approach of scanning, roaming delays are observed.
Firmware has support for back ground scanning. To get this advantage,
mac80211 hardware scan is implemented, which decides type of scan to
do based on connected state.
When station is in not connected, driver returns with special value 1
to trigger software scan in mac80211. In case of connected state,
background scan will be triggered.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
common->init_done flag should set after basic initialization. Hence,
moving init_done flag at end of rsi_91x_init().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
rx_params are getting updated two times in driver, which is not required.
Hence, removing duplicate updation of rx_params from rsi_prepare_skb().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Operating mode determines the support for other protocols.
This is made as module parameter for better usage.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
BT frames are passed through coex and hal modules to BUS.
After firmware is loaded, based on the operating mode CARD
READY frame comes for each protocol. When BT card ready is
received, BT attach is called.
Protocol operations are exchanged between the modules
at initialization time.
Build flag CONFIG_RSI_COEX is introduced to enable coex support
if CONFIG_BT_RSIHCI is enabled. Coex operations are valid if
coex mode is greater than 1 only.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With BT support, driver has to handle two streams of data
(i.e. wlan and BT). Actual coex implementation is in firmware.
Coex module just schedule the packets to firmware by taking them
from the corresponding paths.
Structures for module and protocol operations are introduced for
this purpose. Protocol operations structure is global structure
which can be shared among different modules. Move initialization
of coex and operating mode values to rsi_91x_init().
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Rx bluetooth endpoint shall be added in further patches. Rx control
block is introduced here to handle Rx packets properly. Separate
function is written to initialize the RX control blocks.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We are disabling of interrupts from firmware in freeze handler.
Also setting power management capability KEEP_MMC_POWER to make
device wakeup for WoWLAN trigger.
At restore, we observed a device reset on some platforms. Hence
reloading of firmware and device initialization is performed.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We will dump information about firmware version, firmware file
name and operating mode during initialization.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remain-on-channel and cancel-remain-on-channel are implemented
to support p2p listen phase.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support for legacy power save. Necessary
configuration frames are downloaded to firmware when power save
is enabled/disabled
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We have now added separate lock for Rx. This lock is used to protect
tx path only
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Deadlock issue is observed during our stress tests. The root
cause for the issue is same lock is used between tx and rx threads.
This patch adds a separate mutex lock for rx thread to resolve
the problem.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
RS9113 chipset supports Coex feature. Initial frame exchanges during
device initialization happens on coex queue. This patch adds the
handling for coex queue.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Emit a prefix for the rsi_dbg messages.
Fix the format and argument mismatch and add
__printf(2, 3) to try to avoid more.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is to address reports of this:
In file included from drivers/net/wireless/rsi/rsi_mgmt.h:22:0,
from drivers/net/wireless/rsi/rsi_91x_core.c:17:
drivers/net/wireless/rsi/rsi_91x_core.c: In function 'rsi_dbg':
drivers/net/wireless/rsi/rsi_main.h:44:20: error: function 'rsi_dbg' can never be inlined because it uses variable argument lists
static inline void rsi_dbg(u32 zone, const char *fmt, ...)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds the Redpine Signals' 91x wireless driver.
Signed-off-by: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
